Front mower

Wiedenmann RMR 180H

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack with roof rack: Hot-dip galvanized screw system Scope of delivery: 7 shelf uprights Height 4,230 mm with foot section Useful depth 1200 mm 21 cantilever arms with 1,200 mm usable depth, with deflector 7 roof beams with 1,500 mm projection pre-drilled for on-site roof structure (*Without wooden purlins and trapezoidal sheets for the roof structure) Including longitudinal and diagonal bracing for 1,900 mm stud spacing Incl. fixing material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per upright 2,700 kg plus roof, wind and snow load (maximum snow load 1.85 kN/m² and wind load zone 2) - Load capacity per cantilever 900 kg - including roof girder (maximum snow load 1.85 kN/m² and wind load zone 2) - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms with a depth of 1,200 mm per stand, with deflector = 4 storage levels on top of each other - Including longitudinal and diagonal bracing with 1,900 mm center distance - Shelf length: 11,500 mm - Including fastening material (without floor anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. The substrate must be made of concrete, be level and suitable for dowels and be able to bear the acting loads. The customer is responsible for checking and ensuring the ground conditions and load-bearing capacity as well as any official approvals required. Gox2Yen The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: new, Year of construction: 2022, Cantilever rack NEW Data : - H : approx. 400 cm - D : approx. 137 cm - L : approx. 402 cm - Cantilever arms : approx. 120 cm - Axial dimension: 131 cm Dqlf0T - NEW GOODS immediately from stock. - 500 kg load per arm - 2250 kg load per upright - Uprights in hot-dip galvanized. - Cantilever arms in hot-dip galvanized. - Arms are bolted. - Arms adjustable in 200 mm increments. - Levels: Base + 3 storage levels (4 storage levels) Shelf consists of : - 04 x uprights, incl. base approx. 400 cm made of IPE160. - 12 x cantilever arms approx. 120 cm made of IPE 80 - incl. all necessary connecting elements and screws. Why BLT cantilever racking ? - Certified German manufacturer DIN EN 1090 - Made in Germany - All specified load-bearing capacities of the uprights and cantilever arms are statically verifiable at 100% load. - All shelving systems are supplied in a hot-dip galvanized version. They can therefore be installed both indoors and outdoors and do not rust like painted systems. Consistent appearance for many years. - We use the legally prescribed hot-dip galvanized screw fittings in accordance with DIN EN 15048-1 - Long after-sales guarantee - The upright foot and upright back are welded together, providing additional safety and short assembly times, as the feet do not have to be bolted to the upright back. - Bracing made of angle steel, so no adjustment with turnbuckles necessary. This shortens the assembly time. - No slotted hole system, therefore no weakening of the upright profile. Price : 2396,00 € net + statutory value added tax. You will receive an invoice with VAT shown. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: like new (used), Year of construction: 2024, Cantilever rack with roof rack: Hot-dip galvanized screw system Scope of delivery: 7 shelf uprights Height 4,230 mm with foot section Useful depth 1200 mm 21 cantilever arms with 1,200 mm usable depth, with deflector 7 roof beams with 1,500 mm projection pre-drilled for on-site roof structure (*Without wooden purlins and trapezoidal sheets for the roof structure) Including longitudinal and diagonal bracing for 1,900 mm stud spacing Incl. fixing material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: 8Mftmfyvm2 - Sturdy steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per upright 2,700 kg plus roof, wind and snow load (maximum snow load 1.85 kN/m² and wind load zone 2) - Load capacity per cantilever 900 kg - including roof girder (maximum snow load 1.85 kN/m² and wind load zone 2) - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms with a depth of 1,200 mm per stand, with deflector = 4 storage levels on top of each other - Including longitudinal and diagonal bracing with 1,900 mm center distance - Shelf length: 11,500 mm - Including fastening material (without floor anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. The substrate must be made of concrete, be level and suitable for dowels and be able to bear the acting loads. The customer is responsible for checking and ensuring the ground conditions and load-bearing capacity as well as any official approvals required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: new, Year of construction: 2024, carrying capacity per cantilever arm: 140 kg, shelf height: 2,500 mm, total length: 3,150 mm, axle spacing: 1,030 mm, total width: 810 mm, total height: 2,500 mm, load capacity per stand: 560 kg, approx. 3.15 running meters. Cantilever shelf H: 200 cm 140 kg/arm META Multistrong Data : - H : approx. 200 cm - D : approx. 81 cm - L : approx. 315 cm - Cantilever arms : approx. 60 cm - Axial dimension : 103 cm - NEW GOODS immediately from stock. - 140 kg load per arm - 1300 kg load per upright - Uprights in RAL5010 (gentian blue). - Cantilever arms in RAL5010 (gentian blue). - Arms are hooked in and secured with locking bolts. - Arms adjustable in 70 mm increments. - Levels: Base + 3 storage levels (4 storage levels) Shelf consists of : - 04 x uprights, incl. base approx. 200 cm made of IPE120. - 12 x cantilever arms approx. 60 cm made of rectangular profile 40 x 30 mm. - incl. all necessary connecting elements and screws. -- Available immediately Price : 1269,00 € net 1510,11 € gross You will receive an invoice with VAT included. Accessories such as ground anchors, collision protection etc. can also be purchased from us. Transportation : The delivery is carried out on request by our partner forwarding agency, the costs depend on the postal code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Dqlf0J Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: like new (used), Year of construction: 2022, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights Height 4,160 mm with base section 1,200 m usable depth 12 cantilever arms with 1,200 mm usable depth, standard Longitudinal and diagonal braces for 4,000 mm shelf length (spacing 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time 8Med3Imfm7 - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights height 3,000 mm with base section 1,200 mm 12 cantilever arms with 1,200 mm usable depth, standard Including longitudinal and diagonal bracing for 1,300 mm center distance Incl. fastening material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. Bhdwvxp7Zg For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights height 3,500 mm with base section 1,200 mm 12 cantilever arms with 1,200 mm usable depth, standard Including longitudinal and diagonal bracing for 1,300 mm center distance Incl. fastening material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 40 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,500 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. Ibkj8N9 We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Double-sided cantilever rack used: Hot-dip galvanized screw system Scope of delivery: 4 uprights, double-sided Height 4,160 mm with base section 1,200 mm Zirmu3Xa 24 cantilever arms with 1,200 mm depth, standard Including longitudinal and diagonal bracing for 1,300 mm center distance Incl. fastening material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Also available in larger quantities: 20 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per upright side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height-adjustable in 100 mm increments - 6 screw-on cantilever arms and 2 base sections with a depth of 1,200 mm per upright, standard = 4 storage levels on top of each other per upright side - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights Height 4,160 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Longitudinal and diagonal braces for 4,000 mm shelf length (spacing 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm Bfvqg039Uj - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights Height 2,600 mm with base section 1,000 mm usable depth 12 cantilever arms with 1,000 mm usable depth, standard Including longitudinal and diagonal bracing for 1,300 mm spacing Fastening material (screws, nuts and washers) E2Jjtua - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 40 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: as good as new (ex-display), Year of construction: 2024, carrying capacity per cantilever arm: 720 kg, shelf height: 3,500 mm, total length: 4,000 mm, axle spacing: 1,300 mm, total height: 3,500 mm, clearance between the columns: 1,300 mm, load capacity per stand: 2,250 kg, Equipment: double-sided, Double-sided cantilever rack in hot-dip galvanized design: Scope of delivery: 4 double-sided shelving uprights, height 3.5 m, foot section per upright side 1.2 m usable depth and tire protection 24 cantilever arms with angle deflector and 1.2 m usable depth (suspension system) Longitudinal and diagonal braces for 4 m shelf length (spacing 1.3 m) Fastening material (screws, nuts and washers) Net price: € 2,990.00 plus VAT. Detailed description: - Sturdy steel construction made of IPE profiles (screw system) Dm2Prn - Shelf height 3,500 mm - Shelf length 4,000 mm - Load capacity per upright side 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 cantilever arms per upright side with angle deflector (suspension system) (= 4 storage levels per upright side) - Load capacity per cantilever arm 720 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. Delivery for stock items can be made in approx. 1 week after receipt of order. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The substrate must be concrete, level and suitable for dowels and must be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any necessary official approvals are in place. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights height 3,000 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Including longitudinal and diagonal bracing for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 40 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth B8Vvxohvd0 - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Bfr8Aplf7D Scope of delivery: 4 shelf uprights height 2,600 mm with base section 1,000 mm 12 cantilever arms with 1,000 mm depth, standard Including longitudinal and diagonal bracing for 1,300 mm center distance Incl. fastening material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights Height 4,160 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Longitudinal and diagonal braces for 4,000 mm shelf length (spacing 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. Yqd0Qpp The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights height 2,600 mm with base section 1,000 mm 12 cantilever arms with 1,000 mm depth, standard Including longitudinal and diagonal bracing for 1,300 mm center distance Incl. fastening material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg Bb2Felr - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights height 3,000 mm with base section 1,200 mm 12 cantilever arms with 1,200 mm usable depth, standard Including longitudinal and diagonal bracing for 1,300 mm center distance Incl. fastening material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. By2Jzhxi The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 2.56 m with base section 1.0 m usable depth (1.2 m total depth) 12 cantilever arms with 1.0 m usable depth Longitudinal and diagonal braces for 4 m shelf length (spacing 1.3 m) Fastening material (screws, nuts and washers) (*No paint damage!) Net price on collection: € 1,490.00 plus VAT. Delivery possible for an additional charge Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 7016 (anthracite) - Shelf height 2,560 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Made in Germany - Short delivery time - On-site collection possible Burca0Znkz Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. The substrate must be made of concrete, be level and suitable for dowels and be able to bear the acting loads. The customer is responsible for checking and ensuring the ground conditions and load-bearing capacity as well as any official approvals required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights height 3,000 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard B8V7I2Abol Including longitudinal and diagonal bracing for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 40 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2023, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights height 3,500 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Including longitudinal and diagonal bracing for 1,300 mm spacing 072Mnahg Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 40 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,500 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights Height 2,600 mm with base section 1,000 mm usable depth 12 cantilever arms with 1,000 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) 8Mf2Ym029V - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 40 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Used cantilever racking: Screw system in hot-dip galvanized design Stmez8 Scope of delivery: 4 shelf uprights Height 4,160 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Longitudinal and diagonal braces for 4,000 mm shelf length (spacing 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 4,200 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth Longitudinal and diagonal braces for 1,300 mm upright center distance (4,000 mm shelf length) Fastening material (screws, nuts and washers) - (*Delivery or collection in approx. 1 - 2 weeks) - (*No damage to paintwork!) - (*No damaged components!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Net price: € 1,990.00 plus VAT. Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 7016 (anthracite) - Shelf height 4,200 mm - Load capacity per upright 2,200 kg - Foot section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments 0Vpfkzum - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 740 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. Delivery can be made in approx. 1 - 2 weeks after receipt of order. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The surface must be concrete, level and suitable for dowels and must be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any necessary official approvals are in place. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Double-sided cantilever rack used: Hot-dip galvanized screw system Scope of delivery: 4 uprights, double-sided Height 3,500 mm with base sections 1,200 mm each 24 cantilever arms with a depth of 1,200 mm, standard Including longitudinal and diagonal bracing for 1,300 mm center distance Incl. fixing material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Also available in larger quantities: 20 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per upright side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height-adjustable in 100 mm increments - 6 screw-on cantilever arms and 2 base sections with a depth of 1,200 mm per upright, standard = 4 storage levels on top of each other per upright side - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length 4,000 mm 8Shgoiauds - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 4,200 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth Longitudinal and diagonal braces for 1,300 mm upright center distance (4,000 mm shelf length) Fastening material (screws, nuts and washers) - (*No damage to paintwork!) - (*No damaged components!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Net price: € 1,990.00 plus VAT. Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 5010 (gentian blue) - Shelf height 4,200 mm - Load capacity per upright 2,200 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 730 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. E2Jkque We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. Delivery can be made in approx. 1 - 2 weeks after receipt of order. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The substrate must be concrete, level and suitable for dowels and must be able to support the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any necessary official approvals are in place. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2024, Screw system in hot-dip galvanized design: Pick-up price: Icqpoj3Rz Sturdy steel construction made of IPE profiles Shelf height 3500 mm Load capacity per upright 2100 kg Foot section 1200 mm usable depth Cantilever arms height-adjustable in 100 mm increments 3 screw-on cantilever arms per upright Usable depth 1200 mm, standard (= 4 levels) Load capacity per cantilever arm 700 kg Including longitudinal and diagonal bracing Including fastening material (without ground anchors) With assembly instructions and load plates C4 according to DIN standard