CNC 3D Router Machine 400x300mm

CNC-STEP High-Z S-400

Condition: new, Specifications / Technical Data S-400/T CNC-Portal-Router / CNC-Engraving machine With the purchase of the T-variation of High-Z cnc-router you get a proven technology. High-Z/T cnc-routers was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T 3D-cnc-engravers achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machines you’re able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. Here's a video on a unloaded drive with the new High-Z / T. This 3D-milling-machine series is usable in the industrial field as well as for works like engraving, milling, drilling, measuring, cutting and measuring out systems as for example adhering of adhesive on 3D outlines. All cnc-machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all cnc-engraving-machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. Basic equipment of all High-Z CNC-milling machines: Software ConstruCAM-3D limited ( from S-720 and S-400/T ) included !! To use the software CAD CAM ConstruCAM in full screen, you need the milling software version WIN PCNC Economy upward Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! ----- Equipment / Productdetails: •Drive : 4 stepping motor by Nanotec with 2000 steps/rev (1/10 Step) •2 motors for constant tension and compression during milling operation on X-Axis •Guide ways X and Y axle 22 mm / Z Axis 16mm, grinded and with 61hrc hardened surface •Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle •Ball bearings at both sides of ball screws on X and Y axis •Traverse speed of rapid feed: max. 7000 mm/min •Technical resolution : 0,00625 mm ( 1/8 Schritt ) •Reversal error max.: +/- 10µm ( 0,01mm ) •Table size / clamping area: 730 x 400 mm •Traverse Paths: X=400 mm; Y=280 mm; Z= 110 mm •Reference- and limit switch on all axes •Double safety emergency stop button •Energy chain for clean cabling •Total dinemsions incl motors: L x W x H = appr. 730 x 520 x 500mm •Milling Motor anchorage: Euroneck Ø43mm •incl. Software WIN PCNC Light (optional WIN PCNC Economy, USB or professional) Zjhpdyxl •incl. Software ConstruCAM-3D limited ( recommended sell price 1902.81 EUR) •Modular frame for universal application •Weight appr. 31 kg •Complete machine Included 5 driver microstep controller 5 x 3,5 Amps (Zero3) •An approx. 30-minute long introduction during pick up and an unlimted telephone support are included. •An approx. 2 hours long introduction and an installation of software on your brought note book/ PC as well as a explanation of fundamental terms of Corel Draw etc. possible, too. ----- Technical data contained in the price TÜV-certified control system, tailored to the CNC milling machine / CNC engraving machine: • 4-Channel Stepper motor -CNC-Controller with actual SMD-Technology • Main voltage 115 - 240 Volt / 47 - 63 Hz. • Motor current 4 x 3,5 Amper

Condition: new, Why manufacture small parts on large, expensive CNC machining centers when it does a small CNC machine for a fraction of the price as fast and true to size ? A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. Vgv9a7cnn Brass, copper , steel, stainless steel and many other materials can be processed . See information and seek non-binding offer or view a demonstration at our premises , personalized with your material and your record !

Condition: new, Specifications / Technical Data S-400 CNC Router / CNC milling machine / Engraver cnc-step.com/cnc-router/ With the High-Z CNC-router / engraver you purchase an allround talent (optional WIN PCNC Economy, USB or professional). If you want to clampand fix complex workpieces on the worksurface, or, or, or clamp work-pieces in a high bench vise (the cnc milling machine sits on a frame-construction, is driven by 2 motors and therefore allows to be positioned above a piece to be processed). Or if you simply want to do engraving- or drillingjobs…..you can work on a flat surface, with a pieces of sheet MDF fixed to it. Plane it once and you will be able to work with a precision of +-0,02 mm depth. All cnc-machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all cnc milling / engraving machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. Basic equipment of all High-Z CNC-milling and engraving machines: Software ConstruCAM-3D ( from S-720 and S-400/T ) included !! Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! ----- Equipment / Productdetails: •Drive : 4 stepping motor by Nanotec with 1600 steps/rev (1/8 Step) Cfpzdm •2 motors for constant tension and compression during milling operation on X-Axis •Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle •Guide ways X and Y axle 22 mm / Z Axis 16mm, grinded and with 61hrc hardened surface •Ball bearings at both sides of trapezium spindles Tr. 12x3 mm flank lead •Traverse speed of rapid feed: max. 3000 mm/min •Technical resolution: 0,00187 mm ( 1/8 Schritt ) •Reversal error max.: +/- 30µm ( 0,03mm ) •Table size / clamping area: 730 x 400 mm •Traverse Paths: X=400 mm; Y=300 mm; Z= 110 mm •Reference- and limit switch on all axes •Double safety emergency stop button •Energy chain for clean cabling •Total dinemsions incl motors: L x W x H = appr. 730 x 520 x 500mm •Milling Motor anchorage: Euroneck Ø43mm •incl. Software WIN PCNC Light (optional WIN PCNC Economy, USB or professional) •Modular frame for universal application •Weight appr. 31 kg •Complete machine Included 5 driver microstep controller 5x 3,5 Ampere (Zero3) •An approx. 30-minute long introduction during pick up and an unlimted telephone support are included. •An approx. 2 hours long introduction and an installation of software on your brought note book/ PC as well as a explanation of fundamental terms of Corel Draw etc. possible, too.

Condition: new, Specifications / Technical Data S-400/T CNC-Portal-Router / CNC-Engraving machine Grabite marble soapstione slate engraving photo engraving, milling ..... With the purchase of the T-variation of High-Z cnc-router you get a proven technology with a certain icing of the cake. High-Z/T cnc-routers was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T 3D-cnc-engravers achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machines you’re able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. This 3D-milling-machine series is usable in the industrial field as well as for works like engraving, milling, drilling, measuring, cutting and measuring out systems as for example adhering of adhesive on 3D outlines. All cnc-machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all cnc-engraving-machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. A CE compliant commissioning of the CNC machine requires the assembly of the safety enclosure and the suction adapter. Imvh9aw Basic equipment of all High-Z CNC-milling machines: Software ConstruCAM-3D limited ( from S-720 and S-400/T ) included !! Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! ----- Equipment / Productdetails: •Drive : 4 stepping motor by Nanotec with 1600 steps/rev (1/8 Step) •2 motors for constant tension and compression during milling operation on X-Axis •Guide ways X and Y axle 22 mm / Z Axis 16mm, grinded and with 61hrc hardened surface •Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle •Ball bearings at both sides of ball screws on X and Y axis •Traverse speed of rapid feed: max. 7000 mm/min •Technical resolution : 0,00625 mm ( 1/8 Schritt ) •Reversal error max.: +/- 10µm ( 0,01mm ) •Table size / clamping area: 730 x 400 mm •Traverse Paths: X=400 mm; Y=280 mm; Z= 110 mm •Reference- and limit switch on all axes •Double safety emergency stop button •Energy chain for clean cabling •Total dinemsions incl motors: L x W x H = appr. 730 x 520 x 500mm •Milling Motor anchorage: Euroneck Ø43mm •incl. Software ConstruCAM-3D limited •Modular frame for universal application •Weight appr. 31 kg •Complete machine Included 5 driver microstep controller 5 x 3,5 Ampere (Zero3) •An approx. 30-minute long introduction during pick up and an unlimted telephone support are included. •An approx. 2 hours long introduction and an installation of software on your brought note book/ PC as well as a explanation of fundamental terms of Corel Draw etc. possible, too. ----- Technical data contained in the price TÜV-certified control system, tailored to the CNC milling machine / CNC engraving machine: • 4-Channel Stepper motor -CNC-Controller with actual SMD-Technology • Main voltage 115 - 240 Volt / 47 - 63 Hz. • Motor current 4 x 3,5 Ampere • Microstep controller Resolution 1/10-Step / 2000 Steps/Rev. • 4 Connections for 4 brushless Motor / Stepper motor • Connection with parallel port and Software WIN PCNC Light, Economy or

Condition: ready for operation (used), Year of construction: 2016, With documentation, an inspection is possible. Gw8lnfy

Condition: new, GranitoGrav photo engraving system for granite/gravestones and glass (also suitable for glasses and bottles) The CNC unit for photo engraving in stone and glass. The CNC milling machine series High-Z/S-400T with CNC module GranitoGrav including software for the sensational price. Zx9ugh3o Whether on tombstones, Memorial plaques, tile, glass, mirror glass... You simply load your color.- or black and white photo in the CAD-CAM software ConstruCAM-3D ( all software is switchable in english language ) in the module specially developed, specify the output of the desired size and let the milling paths are calculated. This file will be ready to open in the machine software and sent to the machine! It is really easy! A CE compliant commissioning of the CNC machine requires the assembly of the safety enclosure and the suction adapter. No programming skills are required to do so! Software provides all Windows systems ! The CAM software works off your data accurately and in a very short time and created excellent photos in all above mentioned materials with the CNC machine and the GranitoGrav photo module. The operating costs are extremely low here: Diamond-grinding bits cost about 3-4 euro per piece and stand about 3-5 large images in granite. A photo with the size of 300 x 230 mm requires a processing time of 40-50 minutes approximately. Pictures of 15 x 10 cm are already in about 12-15 minutes. Software runs on all Windows systems! The innovation for all stone, natural stone companies, stone processing, tombstones, monument design, etc. Ideal for tombstones and memorials, as well as glass engravings in finest quality. Also, you can create reliefs in marble, etc. with the mobile CNC machine in-depth, from fonts and even 3D bas reliefs ! Here will find quite a few videos to GranitoGrav applications in glass, granite, bottles, glasses, etc.! Youtube Account CNC-STEP Operating principle of GranitoGrav: In the the spindle recording of grinding head with a brushless motor driven each Scheifstift 2, 35 mm shank can be used. Dragging edit the photo or the graphics. All grayscale in the photo is taken into account and regulated the pressure of the grinding tool via a special electronic system and the software so that lighter and darker areas are generated in the material to be processed, which ultimately represent a photo. Also, vector graphics, fonts, etc. can be engraved. We keep ready a font package with Gothic, Greek and Russian fonts (total 230 fonts) for you! This can be even different completed and engraved in different shades of gray. We exhibit at the StoneTec in Nuernberg ! Hall 9, stand 9-135 Visit us ! You are welcome. Pantograf Pantograph Pantografo Pantografi Pantographe pietra nero assoluto fresadora fresatrice fraiseuse Jyrsintae μηχάνημα άλεσμα fraisage machin Freesmachine Frēzēšanas mašīna frezavimo mašinos Фрезерный станок Frezarka Freza Fraesmaskin Frézovací stroj Frézka Фреза

Condition: new, GranitoGrav photo engraving system for granite/gravestones and glass (also suitable for glasses and bottles) The CNC unit for photo engraving in stone and glass. The CNC milling machine series High-Z/S-400T with CNC module GranitoGrav including software for the sensational price. Whether on tombstones, Memorial plaques, tile, glass, mirror glass... You simply load your color.- or black and white photo in the CAD-CAM software ConstruCAM-3D ( all software is switchable in english language ) in the module specially developed, specify the output of the desired size and let the milling paths are calculated. This file will be ready to open in the machine software and sent to the machine! It is really easy! Bzqsp A CE compliant commissioning of the CNC machine requires the assembly of the safety enclosure and the suction adapter. No programming skills are required to do so! Software provides all Windows systems ! The CAM software works off your data accurately and in a very short time and created excellent photos in all above mentioned materials with the CNC machine and the GranitoGrav photo module. The operating costs are extremely low here: Diamond-grinding bits cost about 3-4 euro per piece and stand about 3-5 large images in granite. A photo with the size of 300 x 230 mm requires a processing time of 40-50 minutes approximately. Pictures of 15 x 10 cm are already in about 12-15 minutes. Software runs on all Windows systems! The innovation for all stone, natural stone companies, stone processing, tombstones, monument design, etc. Ideal for tombstones and memorials, as well as glass engravings in finest quality. Also, you can create reliefs in marble, etc. with the mobile CNC machine in-depth, from fonts and even 3D bas reliefs ! Here will find quite a few videos to GranitoGrav applications in glass, granite, bottles, glasses, etc.! Youtube Account CNC-STEP Operating principle of GranitoGrav: In the the spindle recording of grinding head with a brushless motor driven each Scheifstift 2, 35 mm shank can be used. Dragging edit the photo or the graphics. All grayscale in the photo is taken into account and regulated the pressure of the grinding tool via a special electronic system and the software so that lighter and darker areas are generated in the material to be processed, which ultimately represent a photo. Also, vector graphics, fonts, etc. can be engraved. We keep ready a font package with Gothic, Greek and Russian fonts (total 230 fonts) for you! This can be even different completed and engraved in different shades of gray. Pantograf Pantograph Pantografo Pantografi Pantographe pietra nero assoluto fresadora fresatrice fraiseuse Jyrsintae μηχάνημα άλεσμα fraisage machin Freesmachine Frēzēšanas mašīna frezavimo mašinos Фрезерный станок Frezarka Freza Fraesmaskin Frézovací stroj Frézka Фреза

Condition: new, Specifications / Technical Data S-1000/T CNC-Router / CNC-Engraver With the purchase of the T-variation of High-Z CNC-router you get a proven technology. High-Z/T was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T CNC-engraver achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machine you’re able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. This cnc-router series is usable in the industrial field as well as for works like engraving, milling, drilling, measuring, cutting and measuring out systems as for example adhering of adhesive on 3D outlines. All cnc-routers / cnc-milling-machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. Basic equipment of all High-Z CNC-milling machines: Software ConstruCAM-3D limited ( from S-720 and S-400/T ) included !! Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! ----- Equipment / Productdetails: • Drive : 4 stepping motor by Nanotec with 1600 steps/rev (1/8 Step) • 2 motors for constant tension and compression during milling operation on X-Axis • Guide ways X and Y axle 22 mm / Z Axis 16mm, grinded and with 61hrc hardened surface • Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle • Ball bearings at both sides of ball screws on X and Y axis • Traverse speed of rapid feed: max. 7000 mm/min • Technical resolution : 0,00625 mm ( 1/8 Schritt ) • Reversal error max.: +/- 10µm ( 0,01mm ) • Table size / clamping area: 1300 x 700 mm • Traverse Paths: X=1000 mm; Y=580 mm; Z= 110 mm • Reference- and limit switch on all axes • Double safety emergency stop button • Energy chain for clean cabling • Total dinemsions incl motors: L x W x H = appr. 1320 x 840 x 500mm • Milling Motor anchorage: Euroneck Ø43mm • incl. Software WIN PCNC Light (optional WIN PCNC Economy, USB or professional) • incl. Software ConstruCAM-3D limited( recommended sell price full version 1902.81 EUR) • Modular frame for universal application • Weight appr. 51 kg • Complete machine Included 5 driver microstep controller 5 x 3,5 Ampere (Zero3) • An approx. 30-minute long introduction during pick up and an unlimted telephone support are included. • An approx. 2 hours long introduction and an installation of software on your brought note book/ PC as well as a explanation of fundamental terms of Corel Draw etc. possible, too. ----- Technical data contained in the price TÜV-certified control system, tailored to the CNC milling machine / CNC engraving machine: • 4-Channel Stepper motor -CNC-Controller with actual SMD-Technology • Main voltage 115 - 240 Volt / 47 - 63 Hz. Zjhraz2n • Motor current 4 x 3,5 Ampere • Microstep controller Resolution 1/10-Step / 2000 Steps/Rev. • 4 Connections for 4 brushless Motor / Stepper motor • Connection with parallel port and Software WIN

Condition: new, Specifications / Technical Data S-720/T CNC-Engraving-Machine / Milling machine / CNC-Router With the purchase of the T-variation of High-Z CNC-router you get a proven technology. High-Z/T 3D-cnc-engraver was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T cnc milling machines achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machines you’re able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. A CE compliant commissioning of the CNC machine requires the assembly of the safety enclosure and the suction adapter. Here's a video on a unloaded drive with the new High-Z / T. This cnc-machine series is usable in the industrial field as well as for works like engraving, milling, drilling, measuring, cutting and measuring out systems as for example adhering of adhesive on 3D outlines. All cnc-milling-machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all cnc-engraving-machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. Basic equipment of all High-Z CNC-milling machines: Limited Software ConstruCAM-3D ( from S-720 and S-400/T ) included !! Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! ----- Equipment / Productdetails: •Drive : 4 stepping motor by Nanotec with 1600 steps/rev (1/8 Step) •2 motors for constant tension and compression during milling operation on X-Axis •Guide ways X and Y axle 22 mm / Z Axis 16mm, grinded and with 61hrc hardened surface •Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle •Ball bearings at both sides of ball screws on X and Y axis •Traverse speed of rapid feed: max. 7000 mm/min •Technical resolution : 0,00625 mm ( 1/8 Schritt ) •Reversal error max.: +/- 10µm ( 0,01mm ) •Table size / clamping area: 1050 x 520 mm •Traverse Paths: X=720 mm; Y=400 mm; Z= 110 mm •Reference- and limit switch on all axes •Double safety emergency stop button •Energy chain for clean cabling •Total dinemsions incl motors: L x W x H = appr. 1070 x 690 x 500mm •Milling Motor anchorage: Euroneck Ø43mm •incl. Software ConstruCAM-3D •Modular frame for universal application •Weight appr. 41 kg •Complete machine Includet 5 driver microstep controller 5x 3,5 Ampere (Zero3) •An approx. 30-minute long introduction during pick up and an unlimted telephone support are included. •An approx. 2 hours long introduction and an installation of software on your brought note book/ PC as well as a explanation of fundamental terms of Corel Draw etc. possible, too. ----- Technical data contained in the price TÜV-certified control system, tailored to the CNC milling machine / CNC milling machine: - 4-Channel Stepper motor -CNC-Controller with actual SMD-Technology - Main voltage 115 - 240 Volt / 47 - 63 Hz. - Motor current 4 x 3,5 Ampere - Microstep controller Resolution 1/10-Step / 2000 Steps/Rev. - 4 Connections for 4 brushless Motor / Stepper motor - Connection with parallel port and Soft Zjkxcgey

Condition: new, Specifications / Technical Data S-720 Bzbdf CNC-Router / CNC-Engraver / Milling machine With the High-Z cnc router and engraving machine you purchase an allround talent. If you want to clampand fix complex workpieces on the worksurface, or, or, or clamp work-pieces in a high bench vise (the cnc milling machine sits on a frame-construction, is driven by 2 motors and therefore allows to be positioned above a piece to be processed). Or if you simply want to do engraving- or drillingjobs…..you can work on a flat surface, with a pieces of sheet MDF fixed to it. Plane it once and you will be able to work with a precision of +-0,02 mm depth. All cnc routers / milling machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all cnc milling machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. Basic equipment of all High-Z CNC-milling and engraving machines / routers: Software ConstruCAM-3D ( from S-720 and S-400/T ) included !! Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! ----- Equipment / Productdetails: •Drive : 4 stepping motor by Nanotec with 1600 steps/rev (1/8 Step) •2 motors for constant tension and compression during milling operation on X-Axis •Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle •Guide ways X and Y axle 22 mm / Z Axis 16mm, grinded and with 61hrc hardened surface •Ball bearings at both sides of trapezium spindles Tr. 12x3 mm flank lead •Traverse speed of rapid feed: max. 2500 mm/min •Technical resolution: 0,00187 mm ( 1/8 Schritt ) •Reversal error max.: +/- 30µm ( 0,03mm ) •Table size / clamping area: 1050 x 520 mm •Traverse Paths: X=720 mm; Y=420 mm; Z= 110 mm •Reference- and limit switch on all axes •Double safety emergency stop button •Energy chain for clean cabling •Total dinemsions incl motors: L x W x H = appr. 1070 x 690 x 500mm •Milling Motor anchorage: Euroneck Ø43mm •incl. Software ConstruCAM-3D •Modular frame for universal application •Weight appr. 41 kg •Complete machine Includet 5 driver microstep controller 5x 3,5 Ampere •An approx. 30-minute long introduction during pick up and an unlimted telephone support are included. •An approx. 2-3 hours long introduction and an installation of software on your brought note book/ PC as well as a explanation of fundamental terms of Corel Draw etc. possible, too. ----- Technical data of included microstep controller: •5-channel control •Power up to 5 x 3.5 A •Micro pacing 1/10-Step / 2000 steps / rev. •5 ports for 5 stepper motors •Connection to parallel port or in WIN PCNC Economy to USB port •"Sleep function" for power reduction in standby •Protect against high voltage spikes •E-stop button, 2-way secured •Control of 2 power-consumers up to 1200 watts via software switchable (from WIN PCNC Economy), 230 V, 8A •Power Supply Relay / Cooling •Aluminum heatsink / 2 active fans 60 & 40mm •Ability to connect a total of 5 end-and reference switches / stop button •Ports motors and control line through D-sub 9-pin. ----- fresadora fresatrice fraiseuse Jyrsintae μηχάνημα άλεσμα fraisage machin Freesmachine Frēzēšanas mašīna frezavimo mašinos Фрезерный стано

Condition: new, Specifications / Technical Data S-1000 CNC-Router and CNC-Engraver Zjj2nfz2 This is the biggest machine of our High-Z cnc-router series. With external dimensions of approx. 1350x800mm it is still very handy. With the High-Z 3D-cnc-routers you purchase an allround talent. If you want to clampand fix complex workpieces on the worksurface, or, or, or clamp work-pieces in a high bench vise (the cnc-machine sits on a frame-construction, is driven by 2 motors and therefore allows to be positioned above a piece to be processed). Or if you simply want to do engraving- or drillingjobs…..you can work on a flat surface, with a pieces of sheet MDF fixed to it. Plane it once and you will be able to work with a precision of +-0,02 mm depth. All cnc-machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all cnc-milling machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. Basic equipment of all High-Z CNC-milling machines: Software ConstruCAM-3D limited ( from S-720 and S-400/T ) included !! To use the software CAD CAM ConstruCAM in full screen, you need the milling software version WIN PCNC Economy upward Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! ----- Equipment / Productdetails: •Drive : 4 stepping motor by Nanotec with 1600 steps/rev (1/8 Step) •2 motors for constant tension and compression during milling operation on X-Axis •Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle •Guide ways X and Y axle 22 mm / Z Axis 16mm, grinded and with 61hrc hardened surface •Ball bearings at both sides of trapezium spindles Tr. 12x3 mm flank lead •Traverse speed of rapid feed: max. 2000 mm/min •Technical resolution: 0,00187 mm ( 1/8 Schritt ) •Reversal error max.: +/- 30µm ( 0,03mm ) •Table size / clamping area: 1330 x 680 mm •Traverse Paths: X=1000 mm; Y=600 mm; Z= 110 mm •Reference- and limit switch on all axes •Double safety emergency stop button •Energy chain for clean cabling •Total dinemsions incl motors: L x W x H = appr. 1350 x 840 x 500mm •Milling Motor anchorage: Euroneck Ø43mm •incl. Software ConstruCAM-3D limited •Modular frame for universal application •Weight appr. 51 kg •Complete machine Included 5 driver microstep controller 5 x 3,5 Ampere (Zero3) •An approx. 30-minute long introduction during pick up and an unlimted telephone support are included. •An approx. 2 hours long introduction and an installation of software on your brought note-book / PC as well as a explanation of fundamental terms of Corel Draw etc. possible, too. ----- Technical data contained in the price TÜV-certified control system, tailored to the CNC milling machine / CNC engraving machine: • 4-Channel Stepper motor -CNC-Controller with actual SMD-Technology • Main voltage 115 - 240 Volt / 47 - 63 Hz. • Motor current 4 x 3,5 Ampere • Microstep controller Resolution 1/10-Step / 2000 Steps/Rev. • 4 Connections for 4 brushless Motor / Stepper motor • Connection with parallel port and Software WIN PCNC Light, Economy or USB with WIN PCNC USB or Profi version. ( Also possible:MACH3, USBCNC, NC-Easy LINUX EMC and LINUX CNC and much other stepper driver software.) • "Sleep-Funct

Condition: new, GranitoGrav photo engraving system for granite/gravestones and glass (also suitable for glasses and bottles) The CNC unit for photo engraving in stone and glass. Wo8xsr The CNC milling machine series High-Z/400-T with CNC module GranitoGrav including software for the sensational price. Whether on tombstones, Memorial plaques, tile, glass, mirror glass... You simply load your color.- or black and white photo in the CAD-CAM software ConstruCAM-3D ( all software is switchable in english language ) in the module specially developed, specify the output of the desired size and let the milling paths are calculated. This file will be ready to open in the machine software and sent to the machine! It is really easy! No programming skills are required to do so! Software provides all Windows systems ! A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. The CAM software works off your data accurately and in a very short time and created excellent photos in all above mentioned materials with the CNC machine and the GranitoGrav photo module. The operating costs are extremely low here: Diamond-grinding bits cost about 3-4 euro per piece and stand about 3-5 large images in granite. A photo with the size of 300 x 230 mm requires a processing time of 40-50 minutes approximately. Pictures of 15 x 10 cm are already in about 12-15 minutes. Software runs on all Windows systems! The innovation for all stone, natural stone companies, stone processing, tombstones, monument design, etc. Ideal for tombstones and memorials, as well as glass engravings in finest quality. Also, you can create reliefs in marble, etc. with the mobile CNC machine in-depth, from fonts and even 3D bas reliefs ! Here will find quite a few videos to GranitoGrav applications in glass, granite, bottles, glasses, etc.! Duplicate link, enter in the browser window and open. YouTube.com/user/Croftmania Operating principle of GranitoGrav: In the the spindle recording of grinding head with a brushless motor driven each Scheifstift 2, 35 mm shank can be used. Dragging edit the photo or the graphics. All grayscale in the photo is taken into account and regulated the pressure of the grinding tool via a special electronic system and the software so that lighter and darker areas are generated in the material to be processed, which ultimately represent a photo. Also, vector graphics, fonts, etc. can be engraved. We keep ready a font package with Gothic, Greek and Russian fonts (total 230 fonts) for you! This can be even different completed and engraved in different shades of gray. Pantograf Pantograph Pantografo Pantografi Pantographe pietra nero assoluto fresadora fresatrice fraiseuse Jyrsintae μηχάνημα άλεσμα fraisage machin Freesmachine Frēzēšanas mašīna frezavimo mašinos Фрезерный станок Frezarka Freza Fraesmaskin Frézovací stroj Frézka Фреза

Condition: new, GranitoGrav photoengraving system for granite/gravestones and glass (also suitable for glasses and bottles) The CNC photo engraving unit in glass and stone. The CNC milling machine series High-Z/S-400T with CNC GranitoGrav module includes the software for an incredible price. Whether on memorial plaques, tombstones, tile, mirror glass, glass... Just simply load your black and white or colour photography into the specially developed module of the ConstruCAM-3D software, then only enter the size of the size your photo should be put out afterwards and then the milling paths can be calculated. This file is opened in the software of the machine and sent to the CNC machine, done! It’s really that easy! No previous knowledge is required for this! The ConstruCAM software edits all of your data precisely and in no time and thus with the GranitoGrav photo module it creates exceptional photos in all materials above-mentioned. Consumption costs are very low: grinding pencils cost about 3 to 4 euro PPU and withstand about 3 to 5 big in granite engraved images. A photo of an approx. format of 300 x 230mm requires approximately a processing time of 40 to 50 minutes. Pictures of 150 x 100mm are already created in almost 12 to 15 minutes time. An innovation for natural stone/stone processing companies, tombstone/monument designers, etc. The machine is versatile because you can also create reliefs in marble or other materials with the mobile CNC machine in-depth. Operating method of GranitoGrav: The grinding head is operated with a motor which is brushless and has a spindle mount, in which each grinding pin with a shank diameter of 2.35mm can be applied. Graphics or photos are edited in a grinding process. All grayscale in the photo is considered and regulated regarding the pressure of the grinding tool via the particular electronic and the special software in order that lighter and darker surfaces are created in the processed material, which ultimately represents a photo. In the same way fonts, vector graphics and more can be engraved. These can even be filled differently and also engraved in various shades of grey. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. Zx90220v

Condition: new, Specifications / Technical Data S-720 CNC-Router / CNC-Engraver / Milling machine With the High-Z cnc router and engraving machine you purchase an allround talent. If you want to clampand fix complex workpieces on the worksurface, or, or, or clamp work-pieces in a high bench vise (the cnc milling machine sits on a frame-construction, is driven by 2 motors and therefore allows to be positioned above a piece to be processed). Or if you simply want to do engraving- or drillingjobs…..you can work on a flat surface, with a pieces of sheet MDF fixed to it. Plane it once and you will be able to work with a precision of +-0,02 mm depth. All cnc routers / milling machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all cnc milling machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. Basic equipment of all High-Z CNC-milling and engraving machines / routers: Software ConstruCAM-3D limited ( from S-720 and S-400/T ) included !! To use the software CAD CAM ConstruCAM in full screen, you need the milling software version WIN PCNC Economy upward Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! ----- Equipment / Productdetails: •Drive : 4 stepping motor by Nanotec with 1600 steps/rev (1/8 Step) •2 motors for constant tension and compression during milling operation on X-Axis •Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle •Guide ways X and Y axle 22 mm / Z Axis 16mm, grinded and with 61hrc hardened surface •Ball bearings at both sides of trapezium spindles Tr. 12x3 mm flank lead •Traverse speed of rapid feed: max. 2500 mm/min •Technical resolution: 0,00187 mm ( 1/8 Schritt ) •Reversal error max.: +/- 30µm ( 0,03mm ) •Table size / clamping area: 1050 x 520 mm •Traverse Paths: X=720 mm; Y=420 mm; Z= 110 mm •Reference- and limit switch on all axes •Double safety emergency stop button •Energy chain for clean cabling •Total dinemsions incl motors: L x W x H = appr. 1070 x 690 x 500mm •Milling Motor anchorage: Euroneck Ø43mm •incl. Software WIN PCNC Light (optional WIN PCNC Economy, USB or professional) •incl. Software ConstruCAM-3D limited ( recommended sell price full version 1902.81 EUR) •Modular frame for universal application •Weight appr. 41 kg •Complete machine Included 5 driver microstep controller 5x 3,5 Ampere (Zero3) •An approx. 30-minute long introduction during pick up and an unlimted telephone support are included. •An approx. 2 hours long introduction and an installation of software on your brought note book/ PC as well as a explanation of fundamental terms of Corel Draw etc. possible, too. ----- Technical data contained in the price TÜV-certified control system, tailored to the CNC milling machine / CNC engraving machine: Bzbfv • 4-Channel Stepper motor -CNC-Controller with actual SMD-Technology • Main voltage 115 - 240 Volt / 47 - 63 Hz. • Motor current 4 x 3,5 Ampere • Microstep controller Resolution 1/10-Step / 2000 Steps/Rev. • 4 Connections for 4 brushless Motor / Stepper motor • Connection with parallel port and Software WIN PCNC Light, Economy or USB with WIN PCNC USB or Profi version. ( Also possible:MACH3, USBCNC, NC-Easy LINUX

Condition: new, Specifications / Technical Data S-720/T CNC-Engraving-Machine / Milling machine / CNC-Router With the purchase of the T-variation of High-Z CNC-router you get a proven technology. High-Z/T 3D-cnc-engraver was conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T cnc milling machines achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this cnc-machines you’re able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. This cnc-machine series is usable in the industrial field as well as for works like engraving, milling, drilling, measuring, cutting and measuring out systems as for example adhering of adhesive on 3D outlines. All cnc-milling-machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all cnc-engraving-machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. Basic equipment of all High-Z CNC-milling machines: Software ConstruCAM-3D limited ( from S-720 and S-400/T ) included !! Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! ----- Equipment / Productdetails: Zjhqcjjm •Drive : 4 stepping motor by Nanotec with 1600 steps/rev (1/8 Step) •2 motors for constant tension and compression during milling operation on X-Axis •Guide ways X and Y axle 22 mm / Z Axis 16mm, grinded and with 61hrc hardened surface •Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle •Ball bearings at both sides of ball screws on X and Y axis •Traverse speed of rapid feed: max. 7000 mm/min •Technical resolution : 0,00625 mm ( 1/8 Schritt ) •Reversal error max.: +/- 10µm ( 0,01mm ) •Table size / clamping area: 1050 x 520 mm •Traverse Paths: X=720 mm; Y=400 mm; Z= 110 mm •Reference- and limit switch on all axes •Double safety emergency stop button •Energy chain for clean cabling •Total dinemsions incl motors: L x W x H = appr. 1070 x 690 x 500mm •Milling Motor anchorage: Euroneck Ø43mm •incl. Software WIN PCNC Light (optional WIN PCNC Economy, USB or professional) •incl. Software ConstruCAM-3D limited ( recommended sell price full version 1902.81 EUR) •Modular frame for universal application •Weight appr. 41 kg •Complete machine Includet 5 driver microstep controller 5 x 3,5 Ampere (Zero3) •An approx. 30-minute long introduction during pick up and an unlimted telephone support are included. •An approx. 2-3 hours long introduction and an installation of software on your brought note book/ PC as well as a explanation of fundamental terms of Corel Draw etc. possible, too. ----- Technical data contained in the price TÜV-certified control system, tailored to the CNC milling machine / CNC engraving machine: • 5-Channel Stepper motor -CNC-Controller with actual SMD-Technology • Main voltage 115 - 240 Volt / 47 - 63 Hz. • Motor current 5 x 3,5 Ampere • Microstep controller Resolution 1/10-Step / 2000 Steps/Rev. • 4 Connections for 4 brushless Motor / Stepper motor • Connection with par

Condition: new, GranitoGrav photo engraving system for granite/gravestones and glass (also suitable for glasses and bottles) The CNC unit for photo engraving in stone and glass. The CNC milling machine series High-Z/400-T with CNC module GranitoGrav including software for the sensational price. Whether on tombstones, Memorial plaques, tile, glass, mirror glass... You simply load your color.- or black and white photo in the CAD-CAM software ConstruCAM-3D ( all software is switchable in english language ) in the module specially developed, specify the output of the desired size and let the milling paths are calculated. This file will be ready to open in the machine software and sent to the machine! It is really easy! No programming skills are required to do so! Software provides all Windows systems ! The CAM software works off your data accurately and in a very short time and created excellent photos in all above mentioned materials with the CNC machine and the GranitoGrav photo module. The operating costs are extremely low here: Diamond-grinding bits cost about 3-4 euro per piece and stand about 3-5 large images in granite. A photo with the size of 300 x 230 mm requires a processing time of 40-50 minutes approximately. Pictures of 15 x 10 cm are already in about 12-15 minutes. Software runs on all Windows systems! The innovation for all stone, natural stone companies, stone processing, tombstones, monument design, etc. Ideal for tombstones and memorials, as well as glass engravings in finest quality. Also, you can create reliefs in marble, etc. with the mobile CNC machine in-depth, from fonts and even 3D bas reliefs ! Here will find quite a few videos to GranitoGrav applications in glass, granite, bottles, glasses, etc.! Duplicate link, enter in the browser window and open. YouTube.com/user/Croftmania Operating principle of GranitoGrav: In the the spindle recording of grinding head with a brushless motor driven each Scheifstift 2, 35 mm shank can be used. Dragging edit the photo or the graphics. All grayscale in the photo is taken into account and regulated the pressure of the grinding tool via a special electronic system and the software so that lighter and darker areas are generated in the material to be processed, which ultimately represent a photo. A CE compliant commissioning of the CNC machine requires the assembly of the safety enclosure and the suction adapter. Also, vector graphics, fonts, etc. can be engraved. We keep ready a font package with Gothic, Greek and Russian fonts (total 230 fonts) for you! This can be even different completed and engraved in different shades of gray. Co7t9fcj Pantograf Pantograph Pantografo Pantografi Pantographe pietra nero assoluto fresadora fresatrice fraiseuse Jyrsintae μηχάνημα άλεσμα fraisage machin Freesmachine Frēzēšanas mašīna frezavimo mašinos Фрезерный станок Frezarka Freza Fraesmaskin Frézovací stroj Frézka Фреза

Condition: new, Specifications / Technical Data S-1400/T CNC-Router and CNC-Engraver / Engraving Machine (Attention: Pictures are showing the type with trapezium spindles, thats the only different to the t-series ) With the purchase of the T-variation of High-Z CNC-router you get a proven technology. High-Z/T cnc-routers are conceived for once more precision (repetition precision approx. 0,02mm) and especially for higher traverse speed. Because of the used ball screws the High-Z/T cnc-machines achieves a fantastic precision and an almost unmeasurable back lash of approx. 0,01mm. At the same time there are high traverse speeds up to approx. 108mm / sec. ( 6.500 mm/min ) possible. With this 3D-cnc-machine you’re able to carry out an engrave and mill speeds of approx. 4500 mm/min. and express travels up to 6500mm/min. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. This 3D-cnc-milling machine series is usable in the industrial field as well as for works like engraving, milling, drilling, measuring, cutting and measuring out systems as for example adhering of adhesive on 3D outlines. With the S-1400 cnc-routers you are able to mill in almost all materials. Additional linear rail ways from HIWIN at X-axis are making the machine extreme stable. With the two trapezium nuts at X and y axis you are able to adjust backlash too. High quality components and a optional underframe leave none wishes open. So you are able to do that too: Milling in a big metall sheet cabinet. Work further like a professional and arrange a demonstration today in our house. All cnc-machines are being delivered with black energy-chains on all axis, which allows a better cabling management. Also, all machines are equipped with an emergency stop button. An additional emergency stop you find in front of the controller. Basic equipment of all High-Z CNC-milling machines: Software ConstruCAM-3D limited ( from S-720 and S-400/T ) included !! To use the software CAD CAM ConstruCAM in full screen, you need the milling software version WIN PCNC Economy upward Contact free reference switch and emergency stop button as well as 22mm thick linear guide ways and individually adapted screw nuts !! Zjhr9kno ----- Equipment / Productdetails: •Drive : 4 stepping motor by Nanotec with 1600 steps/rev (1/8 Step) •2 motors for constant tension and compression during milling operation on X-Axis •Guide ways X 22mm and Y axle 30 mm / Z Axis 16mm, grinded and with 61hrc hardened surface •Feed through of long workpieces possible, because there’s no belt drive at the end of the X-axle •Additional linear guide rails 15mm from HIWIN for the X Axis •Ball bearings at both sides of ball screws on X and Y axis •Traverse speed of rapid feed: max. 7000 mm/min •Technical resolution : 0,0079375 mm ( 1/8 Schritt ) •Reversal error max.: +/- 10µm ( 0,01mm ) •Table size / clamping area: 1730 x 880 mm •Traverse Paths: X=1400 mm; Y=780 mm; Z= 110 mm •Reference- and limit switch on all axes •Double safety emergency stop button •Energy chain for clean cabling •Total dinemsions incl motors: L x W x H = appr. 1750 x 1040 x 500mm •Milling Motor anchorage: Euroneck Ø43mm •incl. Software WIN PCNC Light (optional WIN PCNC Economy, USB or professional) •incl. Software ConstruCAM-3D limited ( recommended sell price full version 1902.81 EUR) •Modular frame for universal application ( shown underframe optional, 980 Euro incl VAT ) •Weight app

Condition: good (used), Year of construction: 2007, For sale is a machining center Mikron type HSM 400 U with 5 axes The machine was used for copper machining (See video) Automation with extra charge Technical data: Year 2007 Heidenhain iTNC 530 42.000 min spindle HSK 40 68 - fold tool changer 50.000 switch-on hours 5 axes X-axis:400 mm Y-axis:240 mm Z-axis:350 mm Outer dimensions: 2400x2100x2400 mm The machine is ready for immediate use and in a good condition 4th and 5th axis have been renewed recently. Service reports, repair history and documentation are available. Erowa Compact Automation additionally available Upon request, disassembly, loading and transport can be organized throughout Europe for an additional charge. Prices plus value added tax Glnld8 Viewing by appointment possible. Contact us, our team is happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES ETC. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For more information or to contact us, please visit our website

Condition: new, Year of construction: 2022, 2-axis CNC rotary table. Oscillating circle 700 mm, face plate 320 mm. High quality duplex gearing. Cdgcyyh8 Also available as direct drive. See picture 2. Technical data URH 320 i DT Faceplate diameter (mm) 320 Load capacity (kg) Horizontal 110 Vertical 70 Accuracy swivel axis ±30" Accuracy rotary axis ±15" Repeatability 4" 2 years warranty.

Condition: used, Year of construction: 1981, x-travel 650 mm y-travel 450 mm workpiece height 585 mm Control ADCOS CNC 400 total power requirement 15 kW weight of the machine ca. 5000 kg dimensions of the machine ca. m H A U S E R (Switzerland) CNC Controlled Hi Precision Double Column Jig Grinder Model S 40 – CNC 311 / ADCOS 400 CNC Year 1981 / CNC modernized in 2008 # 0126 _____ Table size approx. 630 x 770 mm Table load capacity approx. 500 kg Table travel longitudinal max. (X) 650 mm Grinding head slide cross max. (Y) 450 mm Vertical adjustment of cross rail max. (W) 500 mm Grinding spindle stroke max. (Z) 140 mm Stroke number of grinding head (4cycles) 0,5-12 m/min. Vertical distance between Table/grinding spindle 0-585 mm Distance between columns 750 mm Conical grinding max. 16 ° Grinding-Ø bore approx. 230/360 mm 18 spindle speeds depending on spindle motor infinitely variable 4.500-80.000 rpm Fine feeds in X and Y-axis and W-axis 0,5-1.500/3.000/800 mm/min. Planetary speed (C) 5-250 rpm U-axis, radial feed 6 mm By7tu7dask Total electrical load approx. 15 kW - 400 V – 50 cycles Weight approx. 4.500 kg Accessories/ Special Features: • CNC Pathcontrol replaced and modernized into a ADCOS Control Model CNC 400, (German Manufacturer) including large monitor and relevant software, electronic handwheel, for following axis: X=Table length, Y= spindlehead carriage cross, Z= Quill vertical/stroke, C=Quill-Rotation,U=Circular Infeed, w=Vertical adjustment of cross rail. • Z-axis as rapid stroke for shorter processing times, plunge-cut grinding, face grinding, Pre-selection of reversing stops (start movement + teach-in) and of stroke speed (infinitely variable), • U-axis as manual and controlled feed-axis radial, mounted on grinding head, with play of feeding size 1 Grinding motor mounted on spindle, maybe up to a spindle speed of 30.000 rpm, • Mounted accustic grinding contact-display device KSV 5 • Separate standing coolant facility, switching- and control cabinet, separate hydraulic system, central lubrication system, dust suction, etc Condition : very good / can be inspected under power Delivery : ex stock – as inspected Payment : net – after completion of contract

Condition: new, CE-certified water jet cutter flowJET-2015 Pure water system with a 15kW high-pressure pump Manufactured to customer order Delivery time approx. 13 - 16 weeks proven RaptorX-SL technology equipped with quality components from the manufacturers HAMMELMANN® and ALLFI®. different high-pressure pumps with 3800 bar selectable with an output of 15 kW or 30 kW available in different versions as pure water system or as abrasive cutting system the abrasive version is equipped with an abrasive conveyor system with a capacity of 100 kg, an abrasive dosing unit with a capacity of 350 ml and infinitely variable Underwater work is also possible thanks to adjustable water level sensors Abrasive water jet cutting machine can also be used as a pure water cutting system, the other way round is not possible (retrofitting is possible at any time) flowJET-2015 Technical Data Clamping area of 2100 x 1550 mm usable travel range of 2010 x 1510 x 300 mm Weight approx. 1360 kg positioning speed: maximum 30,000 mm/min Working speed: maximum 20,000 mm/min Step size X: 0.0213 mm Step size Y, Z: 0.0113 mm Repeat accuracy: in about 10 µm Backlash: about +/- 45 µm all axes equipped with brushless step motors á 9.4 ampere 3 contactless reference switches (limit switches) on each axis 20 mm HIWIN linear guides, low-backlash planetary gear for the necessary precision Control via three-channel control with 3 x 10 amps Power supply 380 V (50 Hz) KinetiC-NC control software included including CAD-CAM software ConstruCAM-3D design software unlimited and free telephone and TeamViewer support for our customers Cmkehvcc several video tutorials and online help Suitable for all hard materials up to a thickness of about 150 mm Suitable for ceramic tiles, steel, concrete, natural stone and stainless steel The pure water system is suitable for cutting rubber, textiles, thin plastic, foil and thin wood.

Condition: new, CE-certified water jet cutter flowJET-2015 Pure water system with a 30kW high-pressure pump Jvk72i Manufactured to customer order Delivery time approx. 13 - 16 weeks proven RaptorX-SL technology equipped with quality components from the manufacturers HAMMELMANN® and ALLFI®. different high-pressure pumps with 3800 bar selectable with an output of 15 kW or 30 kW available in different versions as pure water system or as abrasive cutting system the abrasive version is equipped with an abrasive conveyor system with a capacity of 100 kg, an abrasive dosing unit with a capacity of 350 ml and infinitely variable Underwater work is also possible thanks to adjustable water level sensors Abrasive water jet cutting machine can also be used as a pure water cutting system, the other way round is not possible (retrofitting is possible at any time) flowJET-2015 Technical Data Clamping area of 2100 x 1550 mm usable travel range of 2010 x 1510 x 300 mm Weight approx. 1360 kg positioning speed: maximum 30,000 mm/min Working speed: maximum 20,000 mm/min Step size X: 0.0213 mm Step size Y, Z: 0.0113 mm Repeat accuracy: in about 10 µm Backlash: about +/- 45 µm all axes equipped with brushless step motors á 9.4 ampere 3 contactless reference switches (limit switches) on each axis 20 mm HIWIN linear guides, low-backlash planetary gear for the necessary precision Control via three-channel control with 3 x 10 amps Power supply 380 V (50 Hz) KinetiC-NC control software included including CAD-CAM software ConstruCAM-3D design software unlimited and free telephone and TeamViewer support for our customers several video tutorials and online help Suitable for all hard materials up to a thickness of about 150 mm Suitable for ceramic tiles, steel, concrete, natural stone and stainless steel The pure water system is suitable for cutting rubber, textiles, thin plastic, foil and thin wood.

Condition: new, CE-certified water jet cutter flowJET-2015 Abrasive cutting unit with 30kW high-pressure pump with abrasive dosing and storage tank Manufactured to customer orderDelivery time approx. 13 - 16 weeks proven RaptorX-SL technology equipped with quality components from the manufacturers HAMMELMANN® and ALLFI®. different high-pressure pumps with 3800 bar selectable with an output of 15 kW or 30 kW available in different versions as pure water system or as abrasive cutting system the abrasive version is equipped with an abrasive conveyor system with a capacity of 100 kg, an abrasive dosing unit with a capacity of 350 ml and infinitely variable Underwater work is also possible thanks to adjustable water level sensors Abrasive water jet cutting machine can also be used as a pure water cutting system, the other way round is not possible (retrofitting is possible at any time) flowJET-2015 Technical Data Clamping area of 2100 x 1550 mm usable travel range of 2010 x 1510 x 300 mm Weight approx. 1360 kg positioning speed: maximum 30,000 mm/min Nwpp2 Working speed: maximum 20,000 mm/min Step size X: 0.0213 mm Step size Y, Z: 0.0113 mm Repeat accuracy: in about 10 µm Backlash: about +/- 45 µm all axes equipped with brushless step motors á 9.4 ampere 3 contactless reference switches (limit switches) on each axis 20 mm HIWIN linear guides, low-backlash planetary gear for the necessary precision Control via three-channel control with 3 x 10 amps Power supply 380 V (50 Hz) KinetiC-NC control software included including CAD-CAM software ConstruCAM-3D design software unlimited and free telephone and TeamViewer support for our customers several video tutorials and online help Suitable for all hard materials up to a thickness of about 150 mm Suitable for ceramic tiles, steel, concrete, natural stone and stainless steel The pure water system is suitable for cutting rubber, textiles, thin plastic, foil and thin wood.

Condition: new, Important and distinguishing design features of the RaptorX SL CNC Router steel base machine RaptorX-SL2200/S15 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objects. Considering our new concept of working with an "invisible" motor for the X-axis and the proven high performance of the entire machine, we will not have to wait long for imitators in the industry to try copy this design. Watch this video in order to get a small foretaste of the performance/speed. Find several other videos of examples being milled in marble, wood, Styrofoam, aluminium etc. here. Overview of the advantages of the RaptorX-SL: (Attention! The pictures show both large and smaller machine types) Zji9yfo8 1.Steel construction of extremely high tortional stability of mainly hot-formed steel profiles with a plate thickness up to 6,3mm ! 2.Highest stability: At a bridge load of 100kg in the middle of the Y axis the bridge of a 2m wide RaptorX-milling machine (travel Y 2010mm) “bends” only 0,02mm, which is only two hundredth of a mm !Therefore even spindles up to approx. 70kg or other heavy tools or tool heads can be used without loss of accuracy of the system ! 3.Variable work space because of adjustable table support struts (optional, price per piece 195 Euro, supports up to approx. 200 kg per strut). Clearance under bridge 150mm, 300mm or 400mm selectable. 4.The framework is open towards the bottom which allows working with tall work pieces (control cabinets, door- and window frames, large three-dimensional parts). 5.New drive concept with planetary gears. This allows traversing speeds up to 40 metres (X + Y axis) per minute (in combination with Mach3, Win PCNC Profi and USB). 6.High speed with maximum performance: three-dimensional drives with Mach3 software up to approx. 10 meters per minute (approx. 170mm per second), depending on contour shape. Therefore the RaptorX-SL almost reaches the performance of a otherwise much more expensive Servo-CNC milling machine ! 7.Unbeatable price-performance ratio! See for yourself! Demonstrations daily by arrangement! Finaly an end to flimsy steel machines constructed of cold drawn, paper thin square tubing which is prone to distortion when welded together. Manufactured from high quality heat-treated steel, the frame construction and 9.4 Amp Brushless drive motors that produce over 900 Ncm holding torque, provide very reliable and stable platforms that are unbeatable in their price to performance ratio. Traverse speeds of up to 40 meters per minute can be achieved. This demonstrates the high quality and performance of our machines. From us you will purchase carefully thought-out technology with the necessary motor control unit as well as high-quality soft

Condition: new, GranitoGrav photo engraving system for granite/gravestones and glass (also suitable for glasses and bottles) The CNC unit for photo engraving in stone and glass. The CNC milling machine series High-Z/400-T with CNC module GranitoGrav including software for the sensational price. Whether on tombstones, Memorial plaques, tile, glass, mirror glass... You simply load your color.- or black and white photo in the CAD-CAM software ConstruCAM-3D ( all software is switchable in english language ) in the module specially developed, specify the output of the desired size and let the milling paths are calculated. This file will be ready to open in the machine software and sent to the machine! It is really easy! No programming skills are required to do so! Software provides all Windows systems ! The CAM software works off your data accurately and in a very short time and created excellent photos in all above mentioned materials with the CNC machine and the GranitoGrav photo module. The operating costs are extremely low here: Diamond-grinding bits cost about 3-4 euro per piece and stand about 3-5 large images in granite. A photo with the size of 300 x 230 mm requires a processing time of 40-50 minutes approximately. Pictures of 15 x 10 cm are already in about 12-15 minutes. Software runs on all Windows systems! The innovation for all stone, natural stone companies, stone processing, tombstones, monument design, etc. Ideal for tombstones and memorials, as well as glass engravings in finest quality. Co77qkwt Also, you can create reliefs in marble, etc. with the mobile CNC machine in-depth, from fonts and even 3D bas reliefs ! Here will find quite a few videos to GranitoGrav applications in glass, granite, bottles, glasses, etc.! YouTube user Croftmania or cnc-step Operating principle of GranitoGrav: In the the spindle recording of grinding head with a brushless motor driven each Scheifstift 2, 35 mm shank can be used. Dragging edit the photo or the graphics. All grayscale in the photo is taken into account and regulated the pressure of the grinding tool via a special electronic system and the software so that lighter and darker areas are generated in the material to be processed, which ultimately represent a photo. Also, vector graphics, fonts, etc. can be engraved. We keep ready a font package with Gothic, Greek and Russian fonts (total 230 fonts) for you! This can be even different completed and engraved in different shades of gray. Pantograf Pantograph Pantografo Pantografi Pantographe pietra nero assoluto fresadora fresatrice fraiseuse Jyrsintae μηχάνημα άλεσμα fraisage machin Freesmachine Frēzēšanas mašīna frezavimo mašinos Фрезерный станок Frezarka Freza Fraesmaskin Frézovací stroj Frézka Фреза

Condition: new, With the T-Rex N-0609 portal milling machines you buy mature technology and long-proven technology combined in one portal machine Machine with CNC control, CADCAM software, control software, control panel, manual central lubrication, multi-zone vacuum table. Due to the robust steel frame construction, vibrations can be damped during the machining process. Thus, the machined workpiece gets clean cutting edges and surfaces. The CNC portal milling machine with helical racks and HWIN / THK / PMI linear slides has a solid cast steel frame. The portal milling machine enjoys great popularity with its robust construction and high stability. Due to the compact base, the machine is ready for use directly at waist height, eliminating the cost of a base as an additional purchased element. Further advantages of the T-Rex portal milling machine Compared to the CNC milling machine from the High-Z T series, the T-Rex portal milling machine has a 100mm greater clearance height between the grooved plate and the Z axis. In this case, the plate material can also be a little thicker in order to still fit under the bridge. This means that you are buying a machine that is unparalleled in its price class, with outstanding precision combined with high stability, maximum ease of operation and an attractive appearance. Iteunet Travel X-axis 900 mm Y-axis travel 600 mm Z-axis travel 200 mm Passage height 200 mm (optional 300/400mm) Clamping surface X / Y on grooved plate 930 x 630 mm length x width x height 165 x 144 x 195 cm Weight 650 kg backlash +/- 0,015 Repeatability ± 10 ?m feed speed 17.000 mm/min Working speed max. 12.000 mm/min

Condition: new, Important and distinguishing design features of the RaptorX SL steel base machine The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. Cahuqpbp It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objects. Considering our new concept of working with an "invisible" motor for the X-axis and the proven high performance of the entire machine, we will not have to wait long for imitators in the industry to try copy this design. Watch this video in order to get a small foretaste of the performance/speed. Find several other videos of examples being milled in marble, wood, Styrofoam, aluminium etc. here. Overview of the advantages of the RaptorX-SL: (Attention! The pictures show both large and smaller machine types) 1.Steel construction of extremely high tortional stability of mainly hot-formed steel profiles with a plate thickness up to 6,3mm ! 2.Highest stability: At a bridge load of 100kg in the middle of the Y axis the bridge of a 2m wide RaptorX-milling machine (travel Y 2010mm) “bends” only 0,02mm, which is only two hundredth of a mm !Therefore even spindles up to approx. 70kg or other heavy tools or tool heads can be used without loss of accuracy of the system ! 3.Variable work space because of adjustable table support struts (optional, price per piece 195 Euro, supports up to approx. 200 kg per strut). Clearance under bridge 150mm, 300mm or 400mm selectable. 4.The framework is open towards the bottom which allows working with tall work pieces (control cabinets, door- and window frames, large three-dimensional parts). 5.New drive concept with planetary gears. This allows traversing speeds up to 40 metres (X + Y axis) per minute (in combination with Mach3, Win PCNC Profi and USB). 6.High speed with maximum performance: three-dimensional drives with Mach3 software up to approx. 10 meters per minute (approx. 170mm per second), depending on contour shape. Therefore the RaptorX-SL almost reaches the performance of a otherwise much more expensive Servo-CNC milling machine ! 7.Unbeatable price-performance ratio! See for yourself! Demonstrations daily by arrangement! Finaly an end to flimsy steel machines constructed of cold drawn, paper thin square tubing which is prone to distortion when welded together. Manufactured from high quality heat-treated steel, the frame construction and 9.4 Amp Brushless drive motors that produce over 900 Ncm holding torque, provide very reliable and stable platforms that are unbeatable in their price to performance ratio. Traverse speeds of up to 40 meters per minute can be achieved. This demonstrates the high quality and performance of our machines. From us you will purchase carefully thou

Condition: new, Important and distinguishing design features of the RaptorX SL steel base gantry machine RaptorX-SL1200/S15 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objects. Considering our new concept of working with an "invisible" motor for the X-axis and the proven high performance of the entire machine, we will not have to wait long for imitators in the industry to try copy this design. Ik3a7g0 Watch this video in order to get a small foretaste of the performance/speed. Find several other videos of examples being milled in marble, wood, Styrofoam, aluminium etc. here. Overview of the advantages of the RaptorX-SL: (Attention! The pictures show both large and smaller machine types) 1.Steel construction of extremely high tortional stability of mainly hot-formed steel profiles with a plate thickness up to 6,3mm ! 2.Highest stability: At a bridge load of 100kg in the middle of the Y axis the bridge of a 2m wide RaptorX-milling machine (travel Y 2010mm) “bends” only 0,02mm, which is only two hundredth of a mm !Therefore even spindles up to approx. 70kg or other heavy tools or tool heads can be used without loss of accuracy of the system ! 3.Variable work space because of adjustable table support struts (optional, price per piece 195 Euro, supports up to approx. 200 kg per strut). Clearance under bridge 150mm, 300mm or 400mm selectable. 4.The framework is open towards the bottom which allows working with tall work pieces (control cabinets, door- and window frames, large three-dimensional parts). 5.New drive concept with planetary gears. This allows traversing speeds up to 40 metres (X + Y axis) per minute (in combination with Mach3, Win PCNC Profi and USB). 6.High speed with maximum performance: three-dimensional drives with Mach3 software up to approx. 10 meters per minute (approx. 170mm per second), depending on contour shape. Therefore the RaptorX-SL almost reaches the performance of a otherwise much more expensive Servo-CNC milling machine ! 7.Unbeatable price-performance ratio! See for yourself! Demonstrations daily by arrangement! Finaly an end to flimsy steel machines constructed of cold drawn, paper thin square tubing which is prone to distortion when welded together. Manufactured from high quality heat-treated steel, the frame construction and 9.4 Amp Brushless drive motors that produce over 900 Ncm holding torque, provide very reliable and stable platforms that are unbeatable in their price to performance ratio. Traverse speeds of up to 40 meters per minute can be achieved. This demonstrates the high quality and performance of our machines. From us you will purchase carefully thought-out technology with the necessary motor control unit as well as high-quality software included in the packag

Condition: new, The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). 3D engraving, bas reliefs in marble etc. Create and mill, what ever you want ..... The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. A CE compliant commissioning of the CNC machine requires the assembly of the safety enclosure and the suction adapter. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objects. Considering our new concept of working with an "invisible" motor for the X-axis and the proven high performance of the entire machine, we will not have to wait long for imitators in the industry to try copy this design. Watch this video in order to get a small foretaste of the performance/speed. Find several other videos of examples being milled in marble, wood, Styrofoam, aluminium etc. here. Overview of the advantages of the RaptorX-SL: Zjoa7uwh (Attention! The pictures show both large and smaller machine types) 1.Steel construction of extremely high tortional stability of mainly hot-formed steel profiles with a plate thickness up to 6,3mm ! 2.Highest stability: At a bridge load of 100kg in the middle of the Y axis the bridge of a 2m wide RaptorX-milling machine (travel Y 2010mm) “bends” only 0,02mm, which is only two hundredth of a mm !Therefore even spindles up to approx. 70kg or other heavy tools or tool heads can be used without loss of accuracy of the system ! 3.Variable work space because of adjustable table support struts (optional, price per piece 195 Euro, supports up to approx. 200 kg per strut). Clearance under bridge 150mm, 300mm or 400mm selectable. 4.The framework is open towards the bottom which allows working with tall work pieces (control cabinets, door- and window frames, large three-dimensional parts). 5.New drive concept with planetary gears. This allows traversing speeds up to 40 metres (X + Y axis) per minute (in combination with Mach3, Win PCNC Profi and USB). 6.High speed with maximum performance: three-dimensional drives with Mach3 software up to approx. 10 meters per minute (approx. 170mm per second), depending on contour shape. Therefore the RaptorX-SL almost reaches the performance of a otherwise much more expensive Servo-CNC milling machine ! 7.Unbeatable price-performance ratio! See for yourself! Demonstrations daily by arrangement! Finaly an end to flimsy steel machines constructed of cold drawn, paper thin square tubing which is prone to distortion when welded together. Manufactured from high quality heat-treated steel, the frame construction and 9.4 Amp Brushless drive motors that produce over 900 Ncm holding torque, provide very reliable and stable platforms that are unbeatable in their price to performance ratio. Traverse speeds of up to 40 meters per minute can be achieved. This demonstrates the high quality and performance of our machines. From us you will purchase carefully thought-out technology with the nec

Condition: new, All our CNC machines of the series High-Z as well as RaptorX-SL can be converted with very little effort to CNC plasma torch / plasma cutting system / CNC plasma cutter! The plasma cutting unit High-Z PlasCUT-1350 is on the one hand suitable for plasma cutting of sheet metal, brass sheet, brass, aluminum and on the other hand also for wood, PVC milling, etc.. Djkdzkj All this makes it so universally applicable, as rarely a CNC portal milling machine in the price range. It can cut smooth sheet metal up to a dimension of 1 x 1.5m.

Condition: new, CE-certified water jet cutter flowJET-3015 Abrasive cutting unit with 30kW high pressure pump with abrasive dosing and storage tank Manufactured to customer order Delivery time approx. 13 - 16 weeks proven RaptorX-SL technology equipped with quality components from the manufacturers HAMMELMANN® and ALLFI®. different high-pressure pumps with 3800 bar selectable with an output of 15 kW or 30 kW available in different versions as pure water system or as abrasive cutting system the abrasive version is equipped with an abrasive conveyor system with a capacity of 100 kg, an abrasive dosing unit with a capacity of 350 ml and infinitely variable Underwater work is also possible thanks to adjustable water level sensors Abrasive water jet cutting machine can also be used as a pure water cutting system, the other way round is not possible (retrofitting is possible at any time) flowJET-3015 Technical Data Coqkrih Clamping area of 3100 x 1550 mm usable travel range 3010 x 1510 x 300 mm Weight approx. 1760 kg positioning speed: maximum 30,000 mm/min Working speed: maximum 20,000 mm/min Step size X: 0.0213 mm Step size Y, Z: 0.0113 mm Repeat accuracy: in about 10 µm Backlash: about +/- 45 µm all axes equipped with brushless step motors á 9.4 ampere 3 contactless reference switches (limit switches) on each axis 20 mm HIWIN linear guides, low-backlash planetary gear for the necessary precision Control via three-channel control with 3 x 10 amps Power supply 380 V (50 Hz) KinetiC-NC control software included including CAD-CAM software ConstruCAM-3D design software unlimited and free telephone and TeamViewer support for our customers several video tutorials and online help Suitable for all hard materials up to a thickness of about 150 mm Suitable for ceramic tiles, steel, concrete, natural stone and stainless steel The pure water system is suitable for cutting rubber, textiles, thin plastic, foil and thin wood.

Condition: new, CE-certified water jet cutting machine JET-2515 Pure water system with a 15kW high-pressure pump Manufactured to customer order Delivery time approx. 13 - 16 weeks proven RaptorX-SL technology equipped with quality components from the manufacturers HAMMELMANN® and ALLFI®. different high-pressure pumps with 3800 bar selectable with an output of 15 kW or 30 kW available in different versions as pure water system or as abrasive cutting system the abrasive version is equipped with an abrasive conveyor system with a capacity of 100 kg, an abrasive dosing unit with a capacity of 350 ml and infinitely variable Underwater work is also possible thanks to adjustable water level sensors Abrasive water jet cutting machine can also be used as a pure water cutting system, the other way round is not possible (retrofitting is possible at any time) flowJET-2515 Technical Data Clamping area of 2600 x 1550 mm usable travel range of 2510 x 1510 x 300 mm Weight approx. 1560 kg positioning speed: maximum 30,000 mm/min Working speed: maximum 20,000 mm/min Step size X: 0.0213 mm Step size Y, Z: 0.0113 mm Repeat accuracy: in about 10 µm Backlash: about +/- 45 µm all axes equipped with brushless step motors á 9.4 ampere 3 contactless reference switches (limit switches) on each axis 20 mm HIWIN linear guides, low-backlash planetary gear for the necessary precision Control via three-channel control with 3 x 10 amps Power supply 380 V (50 Hz) KinetiC-NC control software included including CAD-CAM software ConstruCAM-3D design software unlimited and free telephone and TeamViewer support for our customers several video tutorials and online help Bh9shqamqy Suitable for all hard materials up to a thickness of about 150 mm Suitable for ceramic tiles, steel, concrete, natural stone and stainless steel The purified water system in the food industry for portioning cakes, bakery products, chocolates, meat, vegetables and fruit

Condition: new, With the servo motor milling machine T-Rex Servo-0609 you buy mature technology and long-proven technique combined with trend-setting servo motor technology. Machine with control panel incl. control system, multi-zone vacuum table, manual central lubrication, CADCAM software, control software Machine dimensions 1650 x 1440 x 2050 mm traversing range 900 x 600 x 200 mm clamping area 930 x 630 mm Passage height Z 220 mm (optional 320 / 420 mm) Weight approx. 700 kg Backlash approx. 0.02 to 0.03 mm Repeat accuracy approx. 0.01 mm Rapid speed diagonal max. 50,000 mm per min. Lyk2j Working speed diagonal max. 35.000 mm per min Drive type Servo motors Yaskawa 400 Watt Linear guides width 20 mm (optional 25 mm) The servo motor CNC milling machine T-Rex Servo-0609 with helical racks and HWIN / THK / PMI linear slides has a solid steel frame. The portal milling machine enjoys great popularity with its robust construction, high stability and extensive basic equipment. Due to the robust steel frame construction, vibrations can be damped during the machining process. Thus, the machined workpiece receives clean cutting edges and surfaces. Further advantages of the servo motor milling machine T-Rex Due to the installed servo motors, high efficiency is brought into the production. Besides, there is a high time-saving in clamping, machining and maintenance. A 200mm high clearance between the vacuum table and the Z-axis also makes it easy to machine taller panel materials, as they fit under the bridge without effort. Versatile applications T-Rex Servo-0609 servo motor milling machine is not only suitable for precise milling work but can also be used for drilling, cutting or engraving. Massive components and the high quality of processing of mechanical components allow the production of workpieces from various materials! Due to the built-in helical racks, the T-Rex servo-mills achieve fantastic accuracy and immense speed and are also very flexible in special sizes and can also be manufactured to customer specifications. CE-compliant commissioning of our CNC milling machines requires the installation of a protective enclosure and exhaust port.

Condition: new, Important and distinguishing design features of the RaptorX SL steel base machine / gantry RaptorX-SL1200/S20 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objects. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. Considering our new concept of working with an "invisible" motor for the X-axis and the proven high performance of the entire machine, we will not have to wait long for imitators in the industry to try copy this design. Watch this video in order to get a small foretaste of the performance/speed. Find several other videos of examples being milled in marble, wood, Styrofoam, aluminium etc. here. Overview of the advantages of the RaptorX-SL: (Attention! The pictures show both large and smaller machine types) 1.Steel construction of extremely high tortional stability of mainly hot-formed steel profiles with a plate thickness up to 6,3mm ! 2.Highest stability: At a bridge load of 100kg in the middle of the Y axis the bridge of a 2m wide RaptorX-milling machine (travel Y 2010mm) “bends” only 0,02mm, which is only two hundredth of a mm !Therefore even spindles up to approx. 70kg or other heavy tools or tool heads can be used without loss of accuracy of the system ! 3.Variable work space because of adjustable table support struts (optional, price per piece 195 Euro, supports up to approx. 200 kg per strut). Clearance under bridge 150mm, 300mm or 400mm selectable. 4.The framework is open towards the bottom which allows working with tall work pieces (control cabinets, door- and window frames, large three-dimensional parts). 5.New drive concept with planetary gears. This allows traversing speeds up to 40 metres (X + Y axis) per minute (in combination with Mach3, Win PCNC Profi and USB). 6.High speed with maximum performance: three-dimensional drives with Mach3 software up to approx. 10 meters per minute (approx. 170mm per second), depending on contour shape. Therefore the RaptorX-SL almost reaches the performance of a otherwise much more expensive Servo-CNC milling machine ! 7.Unbeatable price-performance ratio! See for yourself! Demonstrations daily by arrangement! Finaly an end to flimsy steel machines constructed of cold drawn, paper thin square tubing which is prone to distortion when welded together. Manufactured from high quality heat-treated steel, the frame construction and 9.4 Amp Brushless drive motors that produce over 900 Ncm holding torque, provide very reliable and stable platforms that are unbeatable in their price to performance ratio. Traverse speeds of up to 40 meters per minute can be achieved. This demonstrates the high quality and performance of our machines. Zjjhmj9g From us yo

Condition: new, Important and distinguishing design features of the RaptorX SL steel base machine RaptorX-SL2200/S20 The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objects. Zjjjjldi Considering our new concept of working with an "invisible" motor for the X-axis and the proven high performance of the entire machine, we will not have to wait long for imitators in the industry to try copy this design. Watch this video in order to get a small foretaste of the performance/speed. Find several other videos of examples being milled in marble, wood, Styrofoam, aluminium etc. here. Overview of the advantages of the RaptorX-SL: (Attention! The pictures show both large and smaller machine types) 1.Steel construction of extremely high tortional stability of mainly hot-formed steel profiles with a plate thickness up to 6,3mm ! 2.Highest stability: At a bridge load of 100kg in the middle of the Y axis the bridge of a 2m wide RaptorX-milling machine (travel Y 2010mm) “bends” only 0,02mm, which is only two hundredth of a mm !Therefore even spindles up to approx. 70kg or other heavy tools or tool heads can be used without loss of accuracy of the system ! 3.Variable work space because of adjustable table support struts (optional, price per piece 195 Euro, supports up to approx. 200 kg per strut). Clearance under bridge 150mm, 300mm or 400mm selectable. 4.The framework is open towards the bottom which allows working with tall work pieces (control cabinets, door- and window frames, large three-dimensional parts). 5.New drive concept with planetary gears. This allows traversing speeds up to 40 metres (X + Y axis) per minute (in combination with Mach3, Win PCNC Profi and USB). 6.High speed with maximum performance: three-dimensional drives with Mach3 software up to approx. 10 meters per minute (approx. 170mm per second), depending on contour shape. Therefore the RaptorX-SL almost reaches the performance of a otherwise much more expensive Servo-CNC milling machine ! 7.Unbeatable price-performance ratio! See for yourself! Demonstrations daily by arrangement! Finaly an end to flimsy steel machines constructed of cold drawn, paper thin square tubing which is prone to distortion when welded together. Manufactured from high quality heat-treated steel, the frame construction and 9.4 Amp Brushless drive motors that produce over 900 Ncm holding torque, provide very reliable and stable platforms that are unbeatable in their price to performance ratio. Customized machines with double Z axis etc. can be made up to a travel size of 17.500 x 3010mm !! From us you will purchase carefully thought-out techn

Condition: new, Important and distinguishing design features of the RaptorX SL steel base machine A CE compliant commissioning of our CNC machines requires the assembly of the safety enclosure and the suction adapter. The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). Bzbgj This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objects. Considering our new concept of working with an "invisible" motor for the X-axis and the proven high performance of the entire machine, we will not have to wait long for imitators in the industry to try copy this design. Watch this video in order to get a small foretaste of the performance/speed. Find several other videos of examples being milled in marble, wood, Styrofoam, aluminium etc. here. Overview of the advantages of the RaptorX-SL: (Attention! The pictures show both large and smaller machine types) 1.Steel construction of extremely high tortional stability of mainly hot-formed steel profiles with a plate thickness up to 6,3mm ! 2.Highest stability: At a bridge load of 100kg in the middle of the Y axis the bridge of a 2m wide RaptorX-milling machine (travel Y 2010mm) “bends” only 0,02mm, which is only two hundredth of a mm !Therefore even spindles up to approx. 70kg or other heavy tools or tool heads can be used without loss of accuracy of the system ! 3.Variable work space because of adjustable table support struts (optional). Clearance under bridge 150mm, 300mm or 400mm selectable. 4.The framework is open towards the bottom which allows working with tall work pieces (control cabinets, door- and window frames, large three-dimensional parts). 5.New drive concept with planetary gears. This allows traversing speeds up to 40 metres (X + Y axis) per minute (in combination with Mach3, Win PCNC Profi and USB). 6.High speed with maximum performance: three-dimensional drives with Mach3 software up to approx. 10 meters per minute (approx. 170mm per second), depending on contour shape. Therefore the RaptorX-SL almost reaches the performance of a otherwise much more expensive Servo-CNC milling machine ! 7.Unbeatable price-performance ratio! See for yourself! Demonstrations daily by arrangement! Manufactured from high quality heat-treated steel, the frame construction and 9.4 Amp Brushless drive motors that produce over 900 Ncm holding torque, provide very reliable and stable platforms that are unbeatable in their price to performance ratio. Traverse speeds of up to 40 meters per minute can be achieved. This demonstrates the high quality and performance of our machines. From us you will purchase sophisticated technology with the necessary motor control unit as well as high-quality software included in the package price. For the present, the standard machines will be available in six different travel sizes from

Condition: new, The application range of the RaptorX- SL CNC milling machine is extremely wide due to the adjustable work surface height (variable bridge clearance: 150mm, 300mm or 400mm) plus the travel range of the Z axis of 300mm (at no extra cost). B28tvk The Z axis stability is excellent, allowing you to work as accurately on large 3D objects as one can on flat sheet materials. A CE compliant commissioning of the CNC machine requires the assembly of the safety enclosure and the suction adapter. Use the system as a plasma cutting system or a water jet cutting system, appropriate accessories are available. It is possible to work on work-pieces up to a height of 850mm (steel cabinets etc.) or three-dimensional objects up to a height of approx. 400mm (with 400m long milling cutter). This capability is unusual for machines of this size and mold makers usually use a layered construction method to produce large 3D objects. Considering our new concept of working with an "invisible" motor for the X-axis and the proven high performance of the entire machine, we will not have to wait long for imitators in the industry to try copy this design. Watch this video in order to get a small foretaste of the performance/speed. Find several other videos of examples being milled in marble, wood, Styrofoam, aluminium etc. here. Overview of the advantages of the RaptorX-SL: (Attention! The pictures show both large and smaller machine types) 1.Steel construction of extremely high tortional stability of mainly hot-formed steel profiles with a plate thickness up to 6,3mm ! 2.Highest stability: At a bridge load of 100kg in the middle of the Y axis the bridge of a 2m wide RaptorX-milling machine (travel Y 2010mm) “bends” only 0,02mm, which is only two hundredth of a mm !Therefore even spindles up to approx. 70kg or other heavy tools or tool heads can be used without loss of accuracy of the system ! 3.Variable work space because of adjustable table support struts (optional, price per piece 195 Euro, supports up to approx. 200 kg per strut). Clearance under bridge 150mm, 300mm or 400mm selectable. 4.The framework is open towards the bottom which allows working with tall work pieces (control cabinets, door- and window frames, large three-dimensional parts). 5.New drive concept with planetary gears. This allows traversing speeds up to 40 metres (X + Y axis) per minute (in combination with Mach3, Win PCNC Profi and USB). 6.High speed with maximum performance: three-dimensional drives with Mach3 software up to approx. 10 meters per minute (approx. 170mm per second), depending on contour shape. Therefore the RaptorX-SL almost reaches the performance of a otherwise much more expensive Servo-CNC milling machine ! 7.Unbeatable price-performance ratio! See for yourself! Demonstrations daily by arrangement! Finaly an end to flimsy steel machines constructed of cold drawn, paper thin square tubing which is prone to distortion when welded together. Manufactured from high quality heat-treated steel, the frame construction and 9.4 Amp Brushless drive motors that produce over 900 Ncm holding torque, provide very reliable and stable platforms that are unbeatable in their price to performance ratio. Traverse speeds of up to 40 meters per minute can be achieved. This demonstrates the high quality and performance of our machines. From us you will purchase carefully thought-out technology with the necessary motor control unit as well as high

Condition: new, The portal milling machine T-Rex for 2D, 2.5D and 3D material processing, milling optimized. With 2500 x 1300 mm travel, 200 mm in the Z direction. The scope of delivery also includes the comprehensive CAD-CAM software ConstruCAM-3D. Optional features include high-frequency milling motors, multi-zone vacuum table, safety enclosures, minimum spray cooling, multiple tool change systems with HSK holders, as well as direct change systems and other useful accessories. Machine weight 1550 kg Machine dimensions 3270 x 2150 x 1950 mm clamping area 2530 x 1320 mm Traverse areas (X,Y,Z) 2500 x 1300 mm Passage height 220 mm (optional 320/420 mm) Idle speed (rapid traverse X,Y) 17,000 mm/min Working speed 12.000 mm/min Backlash approx. 0.015 mm Repeat accuracy 0.01 mm Ruq0c9w The robust steel frame construction can damp vibrations during the machining process. Thus, the machined workpiece receives clean cutting edges and surfaces. The CNC portal milling machines from the T-Rex series are equipped with high-quality helical racks on each axis and HIWIN linear guides. The drive stepper motors are designed for milling in aluminium, brass, wood, plastic and many other materials. CE-compliant commissioning of our CNC machines requires the attachment of the protective enclosure and the exhaust port.

Condition: new, The servo CNC milling machine T-Rex Servo-1325 with helical racks and HWIN / THK / PMI linear slide has a solid steel frame. The portal milling machine enjoys great popularity with its robust construction, high stability and extensive basic equipment. Machine including CNC control, CADCAM software, control software, control panel, manual central lubrication, multi-zone vacuum table. traverse area 2500x1300x200 mm clamping area 2530x1320 mm passage height Z max. 220 mm (optional 320/420 mm) Machine dimensions 3270x2150x2100 mm machine weight 1600 kg max. rapid traverse diagonal 50.000 mm per min. max. working speed diagonal 35.000 mm per min. Datdyqaqc drive: Yaskawa 750 Watt servo motors ( optional available with 850 Watt) A 200 mm clearance height between the vacuum table and the Z-axis also makes it easy to process higher panel materials, as they fit under the bridge without difficulty. Solid components and the high quality of workmanship of the mechanical components allow the production of workpieces from various materials! With the built-in helical racks, the T-Rex servo-mills achieve fantastic accuracy and immense speed, and are also very flexible when it comes to special sizes, and can also be made to customer specifications. CE-compliant commissioning of our CNC milling machines requires the installation of a protective enclosure and exhaust port.

Condition: new, CE-certified water jet cutter flowJET-2015 Abrasive cutting unit with 15kW high-pressure pump with abrasive dosing and storage tank for 100kg abrasive Manufactured to customer order Delivery time approx. 13 - 16 weeks proven RaptorX-SL technology equipped with quality components from the manufacturers HAMMELMANN® and ALLFI®. different high-pressure pumps with 3800 bar selectable with an output of 15 kW or 30 kW available in different versions as pure water system or as abrasive cutting system the abrasive version is equipped with an abrasive conveyor system with a capacity of 100 kg, an abrasive dosing unit with a capacity of 350 ml and infinitely variable Underwater work is also possible thanks to adjustable water level sensors Abrasive water jet cutting machine can also be used as a pure water cutting system, the other way round is not possible (retrofitting is possible at any time) flowJET-2015 Technical Data Clamping area of 2100 x 1550 mm usable travel range of 2010 x 1510 x 300 mm Weight approx. 1360 kg positioning speed: maximum 30,000 mm/min Working speed: maximum 20,000 mm/min Step size X: 0.0213 mm Step size Y, Z: 0.0113 mm Repeat accuracy: in about 10 µm Backlash: about +/- 45 µm all axes equipped with brushless step motors á 9.4 ampere 3 contactless reference switches (limit switches) on each axis 20 mm HIWIN linear guides, low-backlash planetary gear for the necessary precision Control via three-channel control with 3 x 10 amps Power supply 380 V (50 Hz) KinetiC-NC control software included including CAD-CAM software ConstruCAM-3D design software Bhxkndd92q unlimited and free telephone and TeamViewer support for our customers several video tutorials and online help Suitable for all hard materials up to a thickness of about 150 mm Suitable for ceramic tiles, steel, concrete, natural stone and stainless steel The pure water system is suitable for cutting rubber, textiles, thin plastic, foil and thin wood.

Condition: excellent (used), Year of construction: 2011, Operating hours: 2,398 h, Machine comes from a joinery and has not been used much Lrywt3ovyx

Condition: used, Metal band saw, band saw machine, vertical band saw -Passage width: 380 mm Muyzwc -Passage height: 230 mm -Table: swiveling -Speeds: 12 pieces min: 45 rpm max: 800 rpm -Dimensions: 1150/715/H1900 mm -Weight: 522 kg

Condition: ready for operation (used), Year of construction: 2015, X-travel: 300mm, y-travel: 200mm, z-travel: 200mm, operating system: Windows 7, software: WinWerth 8.40, weight: 1.5t. Cd002u7vad

Condition: used, Vertical band saw make SAMUR type S 400 Machine # 457 Technical data: Roll diameter 400 mm cutting height 360 mm cutting width 375 mm Table dimension 610 x 610 mm Pivotability of the table to all sides 10 degrees Smallest and largest blade length 3140 - 3440 mm 12 speeds 31 - 948 rpm Dimensions approx. 1150 x 715 x 1900 mm weight approx. 522 kg with Co79reu2 - strip butt welder used

Condition: as good as new (ex-display), Year of construction: 2019, Operating hours: 637 h, used machine wp 1150 bar flow 130 lpm engine Volvo diesel working hours 6,37 h B9t7kect on Truck Scania R 410

Condition: used, head can swivel: 90° (R amp; L) / 45° (F amp; B) Ekhbthm3

Condition: excellent (used), Year of construction: 1999, CTX 400 S2 3 AXIS FROM 1999 Fabricant GILDEMEISTER Modèle CTX 400 Année 1999 Condition used Adresse Frankreich, France Prix Rkapk938 Catégorie Metal Processing Sous catégories Lathes Numéro de stock 1105-03558 Numéro de série Controls CNC, Heidenhain CNC Pilot Country of origin Germany Delivery time IMMEDIATELY Delivery terms ex site, free loaded on truck Turning diameter 570 mm Turning length 635 mm Turning diameter over bed slide 420 mm Spindle turning speed - stepless 25-5000 U/min Number of driven tools 6 mm Drive 5 kW Description CNC HEIDENHAIN Pilot 4232 C-axis with 6 driven toolings 10 FIXED VDI 30 TOOLING 1 CHUCK + CHIP CONVEYOR BAR LOADER SAMSYS

Condition: good (used), Year of construction: 2003, CNC Portal Plasma Cutting Machine Manufacturer: Microstep Type: HS 4001.25 P B78q787lao Year of manufacture: 2003 CNC control: MSNC500P working area: 2500 x 4000 mm 1 plasma torch with power source Kjellberg HiFocus 100 filter system Kemper 8000 MÄ070923

Condition: used, Univers 6 Bccznfraqka cooling through spindle with optional

turning length: 4,000 mm, turning diameter: 1,270 mm, spindle bore: 128 mm, Condition: used, Year of construction: 2000, CNC - high performance lathe Wohlenberg type PT 1 - 1250 II Year of construction 9/2000 with C - axis drive! Hrybm8l7z Technical data: Nominal machining length 4000 mm Center height 665 mm Circumferential diameter U. cross slide 900 mm Swing diameter U. Bed 1270 mm Cross slide travel 800 mm Main spindle head DIN 55027 - 15 Main spindle bore 128 mm Tailstock quill diameter 200 mm Tailstock quill inner taper DIN 55028 - 4 Quill adjustment, manual 350 mm Tailstock adjustment, manual 4000 mm Faceplate, headstock 1200 mm Centering center, headstock MK 6 - 60 degrees Flange centering center, tailstock similar to DIN 55026 - 4- 60 degrees Headstock with C-axis drive Positioning accuracy +/-0.004 degrees 4-fold tool head turret size 32 Tool holder DIN 69881 (VDI 3425 sheet 3) for tool holder nominal size 40 Feed speed X + Z axis 0.75.....6000 mm/min Max. feed force X- and Z-axis 40,000 N Speeds 1 gear stage, infinitely variable 2.24 - 180 rpm 2 gear stages, infinitely variable 9 - 710 rpm C - axis drive (M57) 0.005 - 7.1 rpm Coolant system 100 l/min 8 bar Total connected load 125 kVA Total power requirement 90 kW Space requirement 8600 x 5080 x 3250 mm Switch cabinet (L x W x H) 2800 x 600 x 2050 mm With - CNC path control SINUMERIK 840C - C - axis drive - Lindemaier drilling and milling unit used, in good condition